Sideboard – dividers

Once these go in, the carcase frame is almost complete…

The bottom portion of the case (where the doors and shelves will be) is divided into two compartments. I used a full panel for for this part as it will also be used to hold pins for the shelves.

The panel is made from both eastern white pine and poplar. The exterior and front of the case is eastern white pine. Instead of making the entire dividing panel out of the more expensive pine, I made the first few inches of the panel pine and the rest poplar. The process is the same as gluing up any other panel.

Typically, and as I have in the past, I would use a sliding dovetail to seat the divider panel into the carcase. However, I decided to go with a simple dado. I think mostly because I wanted to practice cutting dados. It turns out it was good practice…and practice that I needed. Each dado was a little better than the previous. There are 6 dados total (two long dados for the large middle panel & two short dados for each drawer divider.

I found that blue tape is a great little helper with this task. It really helped keep my router plane from marrring the surface. The technique I used was to 1) finish the panel to final thickness, including a once over with the smoothing plane, 2) mark out the dados with a marking knife based upon that final thickness of the divider, 3) cut along the knife line with the cross-cut saw down to final depth, 4) chisel out the majority of the waste, and 5) finish up to final depth with the router plane.

This technique worked good, producing a nice square dado. The divider was a little bit of a tight fit, which is what I wanted and expected. I used the smoothing plane to dial in the perfect fit.

web frame dadolarge divider installedfront upper dividerdrawer divider installed

Here I am flushing all the parts before I move onto the top.

divider clean up

– JR

 

 

 

 

 

Advertisements

Sideboard – top web frame

The top web frame comes together with M&T and half blinds…

It will help to hold the carcase together, provide a surface to attach the top, and help to frame the drawers.

I used a little blue tape to help hold things together while I marked out for the half blind dovetails. I spent some time making sure that everything was square before marking to final length.

IMG_5014

I am starting to really like cutting and fitting half blind dovetails. I’m still very new to this type of joinery, as in my past life – as a power tool woodworker – I only cut through dovetails. The half blind seems to come a little more easy to me; there is less fitting and paring with the chisel for me when I cut them. I think I will incorparate them more into future projects.

IMG_5175

After the half blinds were cut and fit properly, the rest of the web frame (middle and sides) were constructed using mortise and tenon joinery. Only the tenons on the front of the case will be glued. The tenons on the back of the case will be free-floating (no glue) so they can move with changes in humdity. I didn’t get a shot of it working, but I got to use my “pigsticker”, which is lots of fun to use. I drove through six mortises in no time with that puppy.

IMG_5025  IMG_5177

Here’s a couple pics of the top web from in place.

IMG_5031  IMG_5030
Next up – the bottom web frame…

-side note…nothing is glued at this point, nor will be for quite some time. I’ll be taking the carcase apart and puting it back together multiple times as I fit some other parts.

-JR

Sideboard – dovetails & rebates

I finally get to some joinery…

I always cut tails first. I do so because, for me, this is the harder of the two (tails or pins) to cut. I also wanted to put the harder, tails on the board that was the hardest to cut. This resulted in cutting the tails on the bottom panel of the carcase.

The bottom panel is 60″ in length, which makes it difficult to work on. I started to cut the tails by clamping the panel to the front of my bench. This worked somewhat, but the top part of the board – where I was sawing – was unsupported and created lots of vibration during the cut. Not something I enjoy – nor does it help me stay square and true while cutting. Not to mention, I had to stand on top of my saw bench to get into the comfortable height in-line with the end of the panel.

That’s how I cut one end of this panel. On the other end, I tried something a little different. I layed the panel flat on my bench and let it hang off the end of the bench a few inches. It was just a matter of “taking a knee” at the end of my bench. The board was much more stable and I was more comfortable.

In the end, both ends turned out good. The second method was much more enjoyable however.

IMG_5003

The corresponding pins on the side panels were a little easier to cut. I was able to clamp these to the front of my bench without all the other issues because of their shorter length. Marking for the tails was the challenge. Luckily I had a third hand to help.

IMG_4996

A little chopping and fine tuning, and I was able to get a glimpse of what the sideboard would look like.

IMG_5004

Looks good…it’s exciting when things start to come together.

Next, I took the opportunity to cut the rebate for the planks that will make up the back of the carcase.

IMG_4998

I think my next chapter in this project will be to work on the top web frame.

-JR

Sideboard – making some panels

Before I begin, I need to make some panels…

This is part of every project that I enjoy. It’s a great way to get into the groove.

I started (bottom, right side, and left side) first cutting all parts to rough length. Here you can see, I lack a saw bench. However, the step stool and upside down chair stool have been serving me well for a while.

IMG_4775

The next step in this process for me is to flatten each board across it’s width. I am also checking, and adjusting, for wind if there is any. There’ my handy-dandy homemade winding sticks.

IMG_4776

These Eastern White Pine boards were in the rough, and came to me significantly over 1″ thick. I removed a lot of wood off each board as there was a decent amount of cupping on every board. This cupping was no match for my #6 jack plane, which I have set up with a very aggressive radius. You might be able to make out the marks from that radius in the photo below. With this nice soft pine, I was able to hog off a ton of material in a short amount of time.

IMG_4779

The shavings bucket was overflowing some.

IMG_4786

From there, I cleaned up one side of each board that I was joining together to make the panels I needed. I purposely leave the other side as is. The reason I don’t flatten and true the other side? Economy of motion (I hope that’s the right saying). I would rather spend my time flattening and truing the entire panel, rather than each board individually…basically saving a step. There’s also another trick I use (using complementary angles to edge glue the boards of a panel together) which I will save for another blog post.

IMG_4781

This is me stickering some panels while they wait for glue-up.

IMG_4789

Here’s the bottom panel and one of the sides. I’m liking the way the grain of this pine is turning out.

IMG_4853

The last thing I had to do to finish preparing these panels was to bring them to final finished dimension – which includes squaring them up. Glad I built that shooting board this winter…it came in handy. Here’s the panels – awaiting their dovetails.

IMG_4934 IMG_4935

Here’s some shop waste piling up. I’ve been to busy sawing and planing to make a run to the compost pile.

IMG_4939

Next, I’ll see if I can get these puppies panels dovetailed…

-JR

Sideboard Layout

Layout is one of the hardest parts for me…

I spent a good portion of the day yesterday laying out parts for the sideboard. I worked through the entire stack, picking out the best fits for the project based upon grain, color, and wood movement potential. It deffinately helps to take the time now and mark everything out.

IMG_4754

I don’t have a dedicated space for my shop. It’s part time shop – part time garage. Therefore, I spent a little extra time restacking the lumber pile in the order that the parts will be used. The boards selected for top and bottom mouldings, for example, are on the bottom of the pile. On top of the pile, are boards like that shown above – bottom & side – which I will use at the start of the project…constructing the carcase.

Glad this task is over…it was tedious, and required some serious brain power. It is becoming evident how invloved this project will be.

IMG_4765 IMG_4762

Now I am tired, but excited to start making some cuts.

-JR

 

 

 

Eastern White Pine Sideboard Kick-off

Feels good to kick-off another project…

Here’s a pic of the design. Clicking on the link will take you to my Sketchup Models page. From there, a click on the pic will take you to the 3D Warehouse in case you would like to download the model.

Buffet

The carcase is constructed with dovetails at the bottom and at the top where it joins a web-frame. There is a second (lower) web-frame that supports the drawers, and also serves to create a division between the drawers and the lower cabinets. There’s also a divider panel that separates the two lower cabinets.

The doors are basic frame and panel construction. They will feature mortise and tenon joinery with a floating panel. The drawers are constructed with half blind dovetails at the front and through dovetails at the back. The “panel” for the bottom of the drawer will float, allowing for wood expansion at the back of the drawer.

I am going to attempt to make my own moulding for the top and bottom moulding on this project. I came up with something for the model, but that design is not yet set in stone. Actually, anything at this point is fair game…I usually make some changes as I work my way through the build.

As I mentioned in the previous post, all the exterior portions of the sideboard (except for the back panels) will feature eastern white pine. All interior portions will be constructed with poplar…the back panels will be poplar as well. The poplar is going to save me some cash, and should wear better on those drawers over time.

Can’t wait to get started…

JR

Lumber run

A took a day off work last week to make a trip to the local lumber yard…

I’m gearing up for my next big project (6′ sideboard). It’s pretty exciting for me as I haven’t really been in the game lately.

The design process usually takes a good amount of time for me, and that’s where I am right now. The design is in it’s final stages, just working out all the fine details (joinery). I should be finished with the design soon. Once finished, I’ll post it and include a link to the 3D Warehouse like usual. The sideboard will feature both drawers and doors, and should end up somewhere around 100 bf of lumber.

The photos below depict all the lumber I should need for the project. There’s about 50bf of Eastern White Pine on the top of the pile, which is intended as the primary wood for the project. On the bottom of the pile, there is about 70 bf of Poplar intended to be used as a secondary wood for all the internal structures.

The lumber is just stacked for now, but it will be stickered once I start to surface it. Right now, everything is in the rough.

IMG_4683 IMG_4680

This was my first trip to this particular lumber yard. The verdict is still out; I’ll have to see how the wood works. The guys out in the yard were very helpful. One of them brought me to the stack of Eastern White Pine and helped me located the boards I was looking for. He then pulled down the stacks with the fork lift and helped me sort through the stacks, board by board, until I found some 16 footers that would work. He then offered to cut them in half so they would fit into my van…I thought this was pretty good service. So, I’ll see how things go with this new supplier over the next few projects. If all is good, perhaps I’ll feature a post on them.

Stayed tuned for the new project design…

-JR